FREE CURB ADDRESS PAINTING WITH SCHEDULED BATHTUB REFINISHING WORK
Services:
BATHTUB AND TILE REFINISHING WORK
Complete refinishing process using an engineered method for long lasting durable products. You can rely on All in 1 Coatings to guide you through every step of the process. We provide the services you need to get your project off the ground and completed in time.
APPLICATIONS
ALL BATHTUBS-CULTURE MARBLE-FIBERGLASS ENCLOSURES & PANS-FORMICA-SINKS-TILE
Additional Add-On Services
- Drain/Overflow trim kits
- Non-slip texture
- Fiberglass foam injection
- Small fiberglass repairs for crack re-inforcement
- Synthetic stone finishes
- Exterior curb address painting
THE PROCESS - WHAT WE DO
All In 1 Coatings in Orange County Ca follows a basic 5-step resurfacing process to refinish or re-glaze your bathtub, counter top, or sinks. While refinishing companies may have techniques or products that differ, the refinishing process itself is generally the same.
1. Clean and Prep Tub
First we clean and scrub out all contaminants, including removal of silicone caulking. Next, we make any initial repairs on bottom and sides of the bathtub.
2. Site preparation
Because bathtub resurfacing is messy, we take the necessary steps to insure that your bathroom is protected from over spray with plastic sheeting taped securely at the edges.
The bathtub refinishing process can produce vapors that may cause irritation, so make sure there is proper ventilation until the process is completed.
3. Sand & Repair
To insure a proper adherence of the re-glazing, we first sand the existing coating adequately to insure a proper bond or remove and strip down entirely.
Any remaining cracks, chips, rust or weak spots are then removed as the last step to prepare for the primer.
4. Primer's include a wipe on for adhesion then 2-3 coats of epoxy resin
A primer is then applied to the bathtub surface and allowed to dry.
5. Coating -Polyurethane
Apply 3 to 4 Different coats of acrylic urethane (which we use a greener material then most are using and follows strict federal V.O.C. laws. (or until we are satisfied that there is enough coverage)
Multiple layers of coating are applied to reglaze and create a new waterproof surface. Once these coats dry, the sealer coat is applied, and your refinishing project is complete.
The bathtub refinishing process is simple. The bathtub will be ready to use after 24 hrs and the now you have a new beautiful tub surface that will last for years!
CARE INSTRUCTIONS
Care Instructions for Bathtub, Tile, Sink, Countertops, Fiberglass Enclosures ETC…
1. DO NOT use the surface for 24 hours upon completion.
2. DO NOT lay soap, sponges, cloths, bottles or any objects on the finish at any time! Purchase a shower rack instead.
3. DO NOT let a leaky faucet go unrepaired!
4. DO NOT use abrasive cleansers. No S-O-S Pads. No Comet/Bleach. No Drano, etc. No Soft Scrub. No razors. NO ABRASIVES AT ALL! Tub cleans easy with spray cleaner and a soft sponge.
5. Here are some good cleansers to use: Foam cleaners are recommended, scrubbing bubbles (BEST read on back will say for refinished porcelain surfaces), Tilex, Lysol Tile Cleaner, Mr. Clean, and Fantastic. NO POWDERS, NO ABRASIVES, make sure no cleaner has bleach in it, just a soft sponge.
6. DO NOT use bath mats with suctions underneath. They may pull at finish and trap moisture.
7. DO NOT pick surface dust off with your finger. Any surface dust will likely dissipate in 3-4 weeks with normal cleaning and usage. Waxing also helps.
8. The best way to keep your tub clean is to wipe it down with a towel after each use. You don't have to wipe it dry.